 |
|
|
 |
|
|
|
| |
TK-2170 |
TK-3170 |
| GENERAL |
Frequency Range
Type 1
Type 3 |
136 ~ 174 MHz
|
440 ~ 480 MHz
400 ~ 430 MHz |
Number of Channels
Zone
Conv. Ch
Trunking GID
|
Max. 128 per Radio
Max. 128 per Zone
|
Max. 128 per Radio
Max. 128 per Zone
Max. 250 per Zone |
Channel spacing
Wide/Narrow |
25, 30 kHz/12.5,15 kHz |
25 kHz/12.5 kHz |
| Battery voltage |
7.5 V DC ± 20 % |
Battery life
(5-5-90 duty cycle, during hi-power, battery saver off)
with KNB-24L (1400mAh)
with KNB-25A (1200mAh)
with KNB-26N (2000mAh)
with KNB-35L (1950mAh)
|
Approx. 9 hours
Approx. 8 hours
Approx. 12 hours
Approx. 11 hours
|
| Operating Temperature Range* |
30º C ~ +60º C |
| Frequency Stability |
±2.5ppm (-30ºC ~ +60ºC) |
| Antenna impedance |
50 Ω |
Channel frequency spread
Type 1
Type 3
|
38 MHz |
40 MHz
30 MHz |
Dimensions (W x H x D)
Projections not Included
Radio Only
with KNB-24L/35L
with KNB-25A/26N
|
56 x 109 x 16.6 mm
56 x 109 x 31.7 mm
56 x 109 x 37.9 mm
|
Weight (net)
Radio Only
with KNB-24L
with KNB-25A
with KNB-26N
with KNB-35L
|
205 g (includes supplied accessories)
350 g [with antenna (KRA-22/23) and belt clip (KBH-12)]
415 g [with antenna (KRA-22/23) and belt clip (KBH-12)]
455 g [with antenna (KRA-22/23) and belt clip (KBH-12)]
340 g [with antenna (KRA-22/23) and belt clip (KBH-12)]
|
| RECEIVER (Measurements made per TIA/EIA-603) |
Sensitivity (12 dB SINAD)
Wide
Narrow |
0.25 μV
0.28 μV |
Selectivity
Wide
Narrow |
70 dB
65 dB |
Intermodulation distortion
Wide
Narrow |
65 dB
60 dB |
| Spurious Response |
65 dB |
| Audio Output (4 Ω impedance)
|
500 mW with less than 5% distortion |
| TRANSMITTER (Measurements made per TIA/EIA-603) |
RF Output Power
High
Low
|
5 W
1 W |
4 W
1 W |
| Spurious Response |
70 dB |
Type of Emission
Wide
Narrow |
16KØ F3E
11KØ F3E |
FFM HUM & Noise
Wide
Narrow |
45 dB
43 dB |
| Audio Distortion |
Less than 5% |
|
*-10ºC ~ +60ºC when KNB-24L/26N/35L in use
Kenwood reserves the right to change specifications and features without prior notice.
FleetSync® is a registered trademark of Kenwood Corporation in the United States and/or other countries.
All other trademarks are property of their respective owners.
|
Applicable MIL-STD & IP
|
| Standard |
MIL 810C
Methods/Procedures |
MIL 810D
Methods/Procedures |
MIL 810E
Methods/Procedures |
MIL 810F
Methods/Procedures |
| Low Pressure |
500.1/Procedure I |
500.2/Procedure I, II |
500.3/Procedure I, II |
500.4/Procedure I, II |
| High Temperature |
501.1/Procedure I, II |
501.2/Procedure I, II |
501.3/Procedure I, II |
501.4/Procedure I, II |
| Low Temperature |
502.1/Procedure I |
502.2/Procedure I, II |
502.3/Procedure I, II |
502.4/Procedure I, II |
| Temperature Shock |
503.1/Procedure I |
503.2/Procedure I |
503.3/Procedure I |
503.4/Procedure I, II |
| Solar Radiation |
505.1/Procedure I |
505.2/Procedure I |
505.3/Procedure I |
505.4/Procedure I |
| Rain |
506.1/Procedure I, II |
506.2/Procedure I, II |
506.3/Procedure I, II |
506.4/Procedure I, III |
| Humidity |
507.1/Procedure I, II |
507.2/Procedure II, III |
507.3/Procedure II, III |
507.4 |
| Salt Fog |
509.1/Procedure I |
509.2/Procedure I |
509.3/Procedure I |
509.4 |
| Dust |
510.1/Procedure I |
510.2/Procedure I |
510.3/Procedure I |
510.4/Procedure I, III |
| Vibration |
514.2/Procedure VIII, X |
514.3/Procedure I |
514.4/Procedure I |
514.5/Procedure I |
| Shock |
516.2/Procedure I, II, V |
516.3/Procedure I, IV |
516.4/Procedure I, IV |
516.5/Procedure I, IV |
| International Protection Standard |
| Dust & Water Protection |
IP54/55 |
|
|
*To meeet MIL 810 and IP grade, the 2-pin connector cover has to be connected.
|
| |
 |
|
|
